Other HVAC
Friedrich PDH07R3SG
$969.00

FRI PDH07R3SG

HVAC

Friedrich PDH07R3SG SG Series PTHCCommercial-Grade, Dependable Performance, and Maximum Comfort Control

It begins with the highest quality materials and components such as stainless steel endplates on the coils and galvanized, zinc-coated steel wall sleeves brought together with durable construction and rigorous testing. These feature-packed Friedrich PTACs are built to deliver years of reliable performance and maximum guest comfort. Quiet, yet powerful airflow quickly reaches all corners with the two motor design and wide-reaching tangential blower wheel.

Guests can select the Constant Fan mode, which produces a steady stream of white noise in both cooling and heating modes that masks sound level changes when the compressor cycles on and off, and also masks outdoor noise.

Comfort Control

Intuitive, user friendly LED display and controls show either set-point or actual room temperature Even heat monitoring automatically adds heat boost if necessary Separate thermostat settings (limiting) for cooling and heating nodes Samples the room temperature every 9 minutes to monitor and maintain desired temperature Optional constant fan mode Reversible indoor air louvers easily change direction of airflow Energy Management System Compatible (Requires additional hardware and service fee. See "Optional Accessories" below)

Sound Reduction Technology

2-motor design allows motors to run at low speeds, reducing indoor noise Quiet, efficient compressor mounted on vibration isolators, which absorb vibration Constant Fan mode provides a steady stream of white noise, masking sound changes when compressor cycles Elongated blower wheel moves air over a wider area, reducing airflow noise Fan turns on before compressor starts to muffle the sound High-density insulation helps keep outdoor noise outside High-density insulation and steel inner wall block outdoor noise

Durability

Advanced anti-corrosion protects outdoor coil against deterioration, especially in harsh coastal environments Galvanized zinc coated steel wall sleeve and steel base pan undergo 11-step preparation process, powder coated with a polyester finish and oven-cured for exceptional durability Additional heating element bottom plate above an improved heat shield provides extra thermal protection Additional thermistor on the blower scroll outlet regulates internal temperature Factory run-tested units reduce problems in the field Room freeze protection initiates heat if temperature falls to 40° Fin an unoccupied room Faultless surehold Front cover system attaches securely Room Freeze Protection initiates heat if room temperature falls to 40 °F in an unoccupied room Random compressor resistant protects electrical systems Stainless Steel endplates on both indoor and outdoor coil Indoor coil frost sensor protects compressor Durable front panel with break-proof control door and design Two permanently lubricated fan motors Tamper-resistant, anodized stamped aluminum grille withstands chalking and oxidation Break-proof control door design maintains the integrity of the unit Indoor coil frost sensor protects the compressor to lengthen the life of the unit. Two permanently lubricated fan motors for added durability Industry leading warranty features 2 year full warranty on parts and labor and 5 year limited warranty

Health and IAQ

Fresh-air vent and damper bring in fresh outside air when desired Easy access anti-microbial filters simplify maintenance andextend the life of the product Dehumidification removes moisture in cool mode to improve comfort and reduce the chance of mold and mildew growth

Energy Usage: Management

Advanced coil design maximizes internal surface area to deliver higher efficiencies providing EERs of up to 13.0 (see specifications for this model's ratings) Increase or decrease electric heat output by changing the power cord Set separate heat and cool range limits Desk control ready to allow hotel owners to control units from a central location (Requires additional hardware. See "Optional Accessories" below) Energy Management System Compatible (Requires additional hardware and service fee. See "Optional Accessories" below) Slinger ring in condensate removal system cools the coil and increases efficiency Electronic temperature limiting to adjust low/high range limits for controlled energy use

Maintenance and Installation Features

Internal diagnostic program alerts maintenance to component failures or operating problems  Fourteen numeric service error codes stored in memory facilitate rapid unit diagnostics Service error code storage Ease of change in heat capacities, which is done by a simple change of power cord (see "Optional Accessories") Remote thermostat pop-out wiring module allows easier wiring and unit change out without rewiring thermostat. May be installed flush with floor Reversible indoor air louvers Improved weather barrier Nationwide Service Network Modular design and pop out wiring modules Modular product design ensures easy access to key components for cleaning and repairs, including washable, lift-out air filters Compact front is designed to preserve indoor floor space with a depth of 7-¾ inches Inner wall service plate provides service access to tangential blower bearing without having to open inner wall Faultless Sure-hold Front Cover System

Specifications

Cooling BTU: 7200 Cooling Watts: 550 Energy Efficiency Ratio (EER): 13 Reverse Heating BTU: 6000 Heating Watts: 485 COP: 3.6 Moisture Removal (pints/hr): 1.7 Sensible Heat Ratio: 0.86 Heating kW Included: 3.5 (can be changed with alternate plug/cord.  See "Optional Accessories") Electric Heat Included: 20 AMP plug NEMA # Receptacle: 7-20R NEMA # Plug: 7-20P Voltage (1-Phase, 60Hz): 265 Volt Range: 292-239 Current (Amps): 2.4 Power Factor: 0.97 Compressor LRA: 12.5 Compressor RLA: 2.2 Outdoor Fan Motor HP: 0.080 CFM, High: 345 CFM, Low: 270 Vent CFM: 75 Sleeve Dimensions (PDXWSA): 16" H X 42" W X 13-3/4" D*  Dimensions with Front: 16" H X 42" W X 21-1/2" D Cut Out Dimensions: 16-1/4" X 42-1/4" Net Weight: 112 Shipping Weight: 132 R-410A Charge (oz): 23

*PDXSWA Sleeve information given for informational purposes only.  Sleeve sold separately

Optional Accessories (sold separately)

Wall SleeveGalvanized steel is prepared in a state-of-the-art, multi-step process for stronger paint adhesion, then powder coated with a polyester finish and cured in an oven for exceptional durability. The wall sleeve is insulated for thermal efficiency and noise reduction. SLEEVE DIMENSIONS: 16" H x 42" W x 13 ¾" D CUT OUT DIMENSIONS: 16 1/4" H x 42 1/4" W FRONT COVER DIMENSIONS: 16" H x 42" W x 7 3/4" DPart #: PDXWSADeep Wall SleevesFor walls up to 17-1/2" deep | Part #: PDXWSEXT18For walls up to 23-1/2" deep| Part #: PDXWSEXT24(Custom depth wall sleeves also available for walls from 13-1/4 to 25-1/2" deep by special order.)Sleeve Extension Retrofit Kit2-1/4" sleeve extension attached to the room side of the sleeve to allow for the installation of a PD-series Friedrich PTAC in an 11-1/2" deep T-series sleeve.Part #: PXSEDigital Remote ThermostatSingle stage cool, single stage heat for PDE models or single stage cool, dual stage heat for PDH model thermostat features high/low fan speed switch. Thermostat is hard wired and can be battery powered or unit powered. Features backlit display and multiple configuration modes.Part #: RT6Digital Wireless Remote ThermostatWireless, single stage, wall-mounted digital thermostat with two fan speeds. Features backlit display and multiple configuration modes.Part #: WRT1FriedrichLink Energy Management ThermostatsWired thermostat with occupancy sensor | Part #: EMRT1Wireless Thermostat with occupancy sensor | Part #: EMWRT1Online Connection KitPart #: EMOCTRemote Access FeeItem #: EMRAFRemote Thermostat Escutcheon KitKit contains escutcheons that can be placed over the factory control buttons when a remote wall mounted thermostat is used. The escutcheon directs the user to the wall thermostat for operation and retains the LED window to display error codes and diagnostic information. 10 pack.Part #: PDXRTAConduit Kit/Junction BoxHard wire conduit kit with junction box for 208/230V and 265V units (subbase not required). Kit includes a means of quick disconnect for easy removal of the chassisPart #: PXCJA

Standard Grille

Standard, stamped, anodized aluminum to resist chalking and oxidation.Part #: PXGAArchitectural GrillesArchitectural grilles that consist of heavy gauge 6063-T5 aluminum alloy.Clear extruded aluminum - Part#: PXAABeige acrylic enamel - Part #: PXBGElectrical SubbaseProvides unit support for walls less than six inches thick.  Includes leveling legs, side filler panels, mounting brackets, a plug-in receptacle and field-wiring access.  The subbase also includes electrical knockouts for a power disconnect switch or circuit breaker.265V 15A - Part #: PXSB26515265V 20A - Part #: PXSB26520265V 30A - Part #: PXSB26530Non-Standard Power Cord Options (3.5kW standard and included on this unit)Select an alternate cord/plug to activate non-standard electric heat selections.2.5kW / 265V / 15A - Part #: PXPC26515A5kW / 265V / 30A - Part #: PXPC26530AAir Filters10-pack of antimicrobial air filters (each PTAC requires 2/ea, sold as 10-pack)Part#: PXFTACondensate Drain KitAttaches to the bottom of the wall sleeve for internal draining of condensate or to the rear wall sleeve flange for external draining.  recommended for all units to remove excess condensate.Part #: PXDR10Lateral Duct Adapter and Lateral Duct ExtensionAttaches to the Friedrich PTAC/PTHP unit to direct up to 355 of the total airflow to a second room.  The unit-mounted duct plenum features a front-mounted aluminum grille that has two posistions to provide the most optimal air direction.  The air may be directed to either the left or the right of the unit through the supplied 3.5" H X 7" W X 47" L plenum.  Plenum may be cut to length by installer.  Kit includes duct plenum, front grille, 47" duct extension, duct discharge grille, duct end cap and all necessary mounting hardware. Additional 3.5" H X 7" W X 47" L plenum for use with the Lateral Duct Adapter.  A maximum of three duct extensions total my be used.  Note: Ducted airflow is reduced as duct length is increased.Part #: PDXDAA/PDXDEA

Download Our Manuals

Currently no manuals available for this product. Please check product description or call our sales support team if you have any further queries.

Application Cooling with Heat Pump
Cooling Capacity (BTU) 7,000 - 7,200
Heating Capacity 5,800 - 6,000 BTU
Voltage 265

Air Conditioner Contractors - Air Conditioner Systems

Get Service Calls